Introducing the Mercury Nano. Tiny, ultra high-quality, multi-output digital audio streamer. Built on the award-winning technology of the PI2AES and Mercury V3, the Mercury Nano has the best sound quality of any streamer you can buy under $1K!
|
|
|
Mercury Nano FAQQ: Do all Mercury Nano outputs work simultaneously?
A: Yes, both AES Balanced and AES Single Ended. Q: Does Mercury Nano support SPDIF? Mercury Nano includes a high quality 75 ohm BNC to RCA adapter for SPDIF use. Q: What power supply does Mercury Nano require? A: Mercury Nano is designed to operate with a nominal input voltage 5V (+/- 10%) 1Amp minimum. Any high quality USB-C PSU will work, switching or linear. Q: But aren't switching supplies bad ? A: Mercury Nano is designed with a highly effective noise filter on the 5V input. This circuit reduces the input supply noise by a factor of 100:1! Q: What Operating Systems does Mercury Nano support? A: Mercury Nano is shipped with a pre-programmed SD Card with Moode Audio. This is a pre-configured image for Mercury Nano. Other Raspberry Pi OS's may be supported. Note that Ropieee DOES NOT support the RTL8152 Ethernet controller used on Mercury Nano. Most other OS'S do support this chip. Q: Where is the WiFi/Bluetooth antenna? A: The enclosure of Mercury Nano is made from 3D printed High Temperature Fiber Reinforced PLA (Polymaker HT-PLA-GF). This material easily passes the RF signals from the internal Raspberry Pi PCB antenna. Q. When can I order a Mercury Nano? A: Limited First Production 50 unit run of Mercury Nano is nearing completion. Ordering will be available starting early November with delivery 1-2 weeks after order. Additional production runs are scheduled to start early Jan. 2027. Mercury Nano Jitter Plot |
Mercury Nano Features Mercury Nano, designed and manufactured by PI 2 Design, is a Raspberry PI3 Model A+ based device designed for Professional, Studio Grade AES Digital Audio Streaming. Mercury Nano converts the Raspberry PI3 A+ I2S Interface to High-Definition Digital Audio Coax and Balanced. These multiple, simultaneously active digital audio outputs allow Mercury Nano to optimally interface with virtually any High-Performance DAC on the market.
The major features of Mercury Nano are as follows: • RASPBERRY PI3 A+ - This Single Board Computer provides 4 High Performance ARM Cores, 4K HDMI Output, 512MB DRAM and more. • ETHERNET - A Realtek RTL8152 100Mbit Ethernet controller is connected to a standard RJ45 • HDMI – A side opening allows access to the HDMI port of the Raspberry PI3 A+. • PCM5102 CLOCK MASTER – A TI PCM5102 is used to provide extremely low jitter clock management for the Mercury Nano. Note – the analog output is unused. • AES TRANSMITTER – The industry standard WM8804 converts the PCM5102 clocks and PI3 A+ I2S data to AES3/SPDIF formatted data at 24-Bit up to the maximum AES Standard data rate of 192Khz. • AES COAX OUTPUT – A 1:1 Isolation Transformer provides Bit Perfect Impedance Controlled Digital Audio Data @ 1V AES Standard Level. • AES BALANCED OUTPUT – A high speed differential transmitter with a 1:1 Isolation Transformer provides balanced audio data via the Professional XLR Connector. • HIGH RESOLUTION CLOCKS – A pair of Ultra-Low Jitter NDK NZ2520SDA oscillators drive the PCM5102 Clock Master for the lowest possible jitter noise. • ULTRA-LOW NOISE LDO’s – Two Ultra-Low Noise, High-PSRR LDO’s supply power to the PCM5102, WM8804 and the NDK Clock’s. • NOISE FILTER – An LC Noise Filter is used to reduce the noise from the input 5V by 100:1. • LOW NOISE PCB LAYOUT – 4-layer Split Ground PCB with noise reduction techniques refined from years of High-Speed Mixed-Signal Design work. • PRE-PROGRAMMED SD CARD - Mercury comes with a pre-programmed SD Card for Moode Audio. MERCURY NANO BLOCK DIAGRAM
|
| mercury_nano_hw_reference_manual_0.1.pdf |
|
|